Universal Strength Machine
1.0 Product Information:
1.1 General Information
Universal Strength Machine is equipped with a loading mechanism and sensing mechanism which are controlled by PLC and observed on screen touch HMI. By default it can measure Compression strength of an AFS (Dia. 2”X2”) or Metric (Dia. 50mmX50mm) Specimen.
With Help of attachment it can also measure
High Compression Strength (Refer 4.2.1)
Shear Strength (Refer 4.2.2)
Splitting Strength (Refer 4.2.3).
Tensile Strength (Refer 4.2.4).
Transverse Strength (Refer 4.2.5).
Twin Transverse Strength (Refer 4.2.6).
Deformation (Refer 4.2.7).
1.2 General Usage
Keep the specimen in between compression pads or accessory & press of start button, within few seconds the equipment shows the reading.
1.3 Product Data
Product Name:
Product Code:
VUD III
Order Reference Code:
V0000108
Electrical Supply Required:
230v 50Hz A.C. (Default)
110v 60 Hz A.C (Optional)
Single Phase, Stabilized with Over/ Under Voltage cut-off.
Electrical Plug:
M type : 15 Amp Plug
Typical Maximum Current:
1.5 A at 230V
Compressed air Supply:
Not Required
Communication:
Ethernet (RJ45)
CloudSync using V-Sync
Dimensions:
545 X 320 X 610 mm (WXBXH)
Packing Dimensions:
650 mmx 420mm x 760 mm (WXBXH) Typical
Net Weight:
Approximately 46 kg
Gross Weight:
Approximately 56 kg
Colour:
Factory Default
Measuring Range:
Direct Load: 300 Kg
Compression: 15 Kg/cm2
Shear/Splitting: 12 Kg/cm2
Tensile : 60 Kg/cm2
Transverse: 600 Kg/cm2
Deformation: 10mm
Traceable to:
NABL Standards
Least Count:
Direct Load: 0.1 Kg
Compression: 0.05 Kg/cm2
Shear/Splitting: 0.05 Kg/cm2
Tensile : 0.05 Kg/cm2
Transverse: 1 Kg/cm2
Twin Transverse: 0.05 Kg/cm2
Deformation: 0.01 mm
Specimen Requirements:
Required
Operating Temperature:
0-500C
Testing Standards:
BIS/AFS
Calibration Frequency:
22500 nos. of Testing Cycles or Once in Year
2.0 Scope of Supply
2.1 Inclusions in Supply Scope
Universal Strength Machine.
Compression pad set.
Calibration certificate.
Instruction manual.
2.2 Exclusions in Supply Scope
Data interfacing accessories.
Anything that is not covered under Supply scope.
3.0 Recommended Pre-requisite Equipment
Sand Splitter : To get representative sample
Specimen preparation equipment’s to make a standard AFS or Metric specimen.
4.0 Accessories
4.1 Calibration Kits
There are two types of calibration kits to choose from:
VKSL: For Low Strength
VKSH: For High Strength
4.2 Attachments
VUHD: High Dry Strength Attachment
VHS: Shear Strength Attachment
VSA: Splitting Strength Attachment
VAS: Tensile Strength Attachment
VTS: Transverse Strength Attachment
VTT: Twin Transverse Shear Attachment
VDSD: Deformation Attachment
5.0 Alternative Equipment
Universal Strength Machine VUD
Universal Strength Machine Hydraulic VUN (For Educational Purposes)
Universal Strength Machine VUM
6.0 Installations Instructions
Required Levelled (2mm) and sturdy platform. (Equipment should be away from external source of vibration or electromagnetic interference.) Other Installation instruction shall be provided along with the equipment.
7.0 Consumables
NA
8.0 Hazards
Squeezing Hazard: Do not insert hand or limb in between the pads when in operation.
9.0 Additional Information
Link to Web-Page
Link to Video of Demo
Disclaimer: Specifications and design of equipment may change without prior notice.
